Exam : Cisco 642-845
Title : Optimizing Converged Cisco Networks


1. Which codec standard would provide the highest voice-quality, mean opinion score (MOS)?
A. G.711, PCM
B. G.728, LDCELP
C. G.729, CS-ACELP
D. G.729A, CS-ACELP
Answer: A

2. Two sites are using a multisite centralized call processing model. The voice gateway on the remote branch has lost IP connectivity to its Cisco CallManager server. Which feature enables the remote gateway to take the role of the call agent during the WAN failure?
A. automated alternate routing (AAR)
B. Cisco CallManager Attendant Console
C. real-time protocol (RTP)
D. Survivable Remote Site Telephony (SRST)
Answer: D

3. Which two statements are true about the function of CAC? (Choose two.)
A. CAC provides guaranteed voice quality on a link.
B. CAC artificially limits the number of concurrent voice calls.
C. CAC is used to control the amount of bandwidth that is taken by a call on a link.
D. CAC prevents oversubscription of WAN resources that is caused by too much voice traffic.
E. CAC allows an unlimited number of voice calls while severely restricting, if necessary, other forms of traffic.
F. CAC solves voice congestion problems by using QoS to give priority to UDP traffic.
Answer: BD

4. Voice activity detection (VAD) suppresses the transmission of silence patterns. On average, and assuming that a link carries at least 24 calls, what percentage of total bandwidth could VAD save?
A. 5
B. 15
C. 25
D. 35
E. 45
F. 55
Answer: D

5. Which two statements regarding the Wireless LAN Solution Engine (WLSE) are true? (Choose two.)
A. To support fault and policy reporting, the WLSE requires a Wireless Control System (WCS).
B. When WLSE detects an AP failure, it automatically increases the power and cell coverage of nearby APs.
C. WLSE requires the 2700 location appliance to offer location tracking.
D. WLSE can locate rogue APs and automatically shut them down.
E. WLSE configuration is done using the command line interface (CLI) or a WEB based template.
Answer: BD

6. Which two statements are true about the implementation of QoS? (Choose two.)
A. Implementing DiffServ involves the configuration of RSVP.
B. Implementing IntServ allows QoS to be performed by configuring only the ingress and egress devices.
C. Implementing IntServ involves the utilization of RSVP.
D. Traffic should be classified and marked by the core network devices.
E. Traffic should be classified and marked as close to the edge of the network as possible.
Answer: CE

7. Which two QoS statements are true about the use of the SDM QoS wizard? (Choose two.)
A. Business-critical traffic includes VoIP and voice signaling packets.
B. SDM can be used to configure a basic QoS policy for incoming traffic on WAN interfaces and IPsec tunnels.
C. SDM can provide QoS for real-time traffic and business-critical traffic.
D. SDM creates a custom-queuing (CQ) or a priority-queuing (PQ) policy.
E. SDM creates a low latency queuing (LLQ) service policy with its associated classes.
F. When allocating bandwidth, values can be entered in either bandwidth percentage or kilobytes per second (kBps).
Answer: CE

8. Refer to the exhibit. Both routers have been configured as VoIP gateways. They must also support traditional telephony devices to connect to analog telephones. Which two configuration changes would correctly support the voice requirements? (Choose two.)
A. On each router, under the dial-peer voice 1 pots configuration, add the port fa0/0 command.
B. On each router, under the dial-peer voice 1 pots configuration, add the port 1/0/0 command.
C. On each router, configure dial-peer voice 1 as a voip connection and configure dial-peer voice 2 as a pots connection.
D. Under the dial-peer voice 1 pots configuration, change the destination pattern of 1111 to 2222 on the R1 router, and 2222 to 1111 on the R2 router.
E. Under the dial-peer voice 2 voip configuration, change the destination pattern of 1111 to 2222 on the R1 router, and 2222 to 1111 on the R2 router.
F. Under the dial-peer voice 2 voip configuration, change the destination target address of 10.2.2.2 to 10.1.1.1 on the R1 router, and the destination target address of 10.1.1.1 to 10.2.2.2 on the R2 router.
Answer: BE